GC Pattern Resin | Acrylic Die Material

13% OFF

Rs.4,650.00 Rs.5,325.00

Out of stock

Available offers

  • SAVE ₹100 Delivery Charges on Order Above ₹5,000.
  • SAVE ₹200 Discount on Order Above ₹10,000.
  • SAVE ₹500 Discount on Order Above ₹20,000.
SKU: AMGC121 Categories: , , , , , , Brand:

Related products

Description

PATTERN RESIN LS is a self-curing, general purpose acrylic resin used for making patterns for fabricating copings, post and core build-ups, lingual and palatal bars, implant attachments, adhesion bridges, clasps, telescoping crowns and certain pre-soldering techniques.This product is formulated to provide a perfect fit. It is ideal for dentists and laboratories who perform difficult restorations due to the fact that it sets quickly with minimal shrinkage, allows both direct and indirect pattern making, and leaves no residue after burnout.
Brand

GC

Benefits

#. Low Polymerization Shrinkage
Greater Accuracy And Dimensional Stability
Improved Defined Margins

#. High Strength; Ultra Smooth Surface
No Distortion
Strength Is Not Compromised, Even In Thin Layers

#. Excellent Fluidity
Easy Manipulation And Handling Due To Thixotrophy
Allows For Direct And Indirect Pattern Making Technique
High Wettability Of Powder And Liquid Very Easily Without Mixing

#. Ash-Free
Leaves No Ash Or Residue After Burn Out
Results In Smoother Cast Surfaces

#. Quick Setting Time
Sets Within 4 Minutes
Sets Significantly Faster Than Any Other Product
Undetectable Corrections And Additions Can Be Made, Even After Set

#. Simply Perfect
Terrific Acrylic Resin
Prosthodontists Favourite

Indications

#. To make the pattern of:

#. Tapered coping for telescopic crowns and other telescope crowns

#. Inlay, palatal and lingual bar, connector and clasp

#. Maryland bridge.

#. Temporary splint for soldering

#. In the mouth for core build up pattern

#. Construction of implant superstructures

KEY Specifications

WARNINGS
The liquid is highly FLAMMABLE. Avoid sources of ignition.
In case of contact with eyes, flush immediately with water and seek medical attention.
PRECAUSTIONS
Do not mix with other chemically cured resins.
Do not return the residual powder and liquid to the bottle.
In case of contact with skin wash off with soap and water.

Directions To USE

Step 1.Powder and liquid preparation Dispense adequate amounts of powder and liquid into each rubber cup.

Step 2. Building the coping (for secondary crown patterns of tapered crowns or telescopic crowns)

a) Moisten the tip of the brush with the liquid and pick up a small amount of powder.
b) Deposit this mixture on the crown and progressively build up the secondary crown pattern by repeating the procedure. In this case, no separating medium is required, but when working on a stone model, GC Acro Sep, GC Multi-Sep or Vaseline should be used as separator. - Clean the brush with liquid after use or during the work if necessary.
Step 3. Checking the internal surface of the pattern After the resin has set (3 min. at 23°C /73°F), remove the pattern carefully from the internal crown and check the margin and the internal surface .

Step 4. Fine adjustment

a) Return the pattern to the internal crown and make a uniform thickness (0.3-0.4 mm) by using a bur.
b) Remove the pattern and check the thickness with the measuring device.
Step 5. Waxing veneer and Cut out

a) Perform the wax-up with inlay wax.
Note: There is no need to clean the surface of the pattern resin with a cleaning agent before waxing.

b) Cut out the veneer for the facing .
c) Place the retention beads.
Step 6. Investing, Burning out and Casting For a single crown, all procedures can be performed in the usual manner. For a larger pattern, hold at 250°C (482°F) for 1 hour before raising to the final burn out temperature.

Packaging

#. 1 X 100G Powder

#. 1 X 105mL Liquid

#. Mixing cups

#. Brush