GC G-Bond Intro Kit

One component Self-Etch light cured Adhesive

4% OFF

Rs.4,300.00 Rs.4,481.00

Out of stock

Available offers

  • SAVE ₹100 Delivery Charges on Order Above ₹5,000.
  • SAVE ₹200 Discount on Order Above ₹10,000.
  • SAVE ₹500 Discount on Order Above ₹20,000.
SKU: AMGC093 Categories: , , Brand:

Description

G-BOND is a new, revolutionary 7th Generation (single component) adhesive that takes the guesswork out of bonding. The unique combination of Phosphoric Acid Ester Monomer and 4-MET Adhesive Technology creates superior etch and adhesion to enamel, in addition to providing a chemical and mechanical seal to dentin (referred to as the Nano Interaction Zone)

7th Generation Bonding Adhesive
Single component
Etch, desensitize, prime and bond in as little as 20 seconds
Not technique sensitive like other “all in one” bonding systems
No post-op sensitivity
Fast and easy application
Strong, reliable, and consistent bond
Stable material; simple storage

Brand

GC

FeaturesFeatures 4-MET Monomer Phospohoric Acid Ester Monomer “Nano Interaction Zone” Technology; an advanced formulation of Phosphoric Acid Ester Monomer, 4-MET Monomer, nanofilled particles, acetone, and water solvents that decalcifies the tooth, providing a wetting property. This diffuses monomer into the tooth structure, polymerizes, hardens when light-cured and creates an ionic bond with the apatite in the tooth structure. Minimal decalcification; almost no exposure to collagen fibers This “nano” level reaction produces an insoluble calcium compound for a better bond 5% filler seals tubules leads to fewer voids between the thin adhesive layer and the dentin, which minimizes microleakage and prevents microbial invasion Benefits For almost any application, in as little as 20-30 seconds, you’re good to go Fast and easy application – just brush G-BOND onto the tooth’s bonding surface, wait 5 to 10 seconds, then air thin with high pressure syringe air and light-cure for 10 seconds Virtually eliminates post-op sensitivity because dentin tubules are never exposed (due to 5% filler) 4-Met Monomer provides consistent bond strength to dentin Phosphoric Acid Ester Monomer provides consistent bond strength to enamel Better bond is less likely to deterioriate from enzymes contained in the mouth Easy clean-up and removal of adhesive overflow Completely coats all bonding surfaces even in an extremely shallow cavity; fewer voids High surface tension makes it easier to apply and remain on all bonding surfaces Bonding layer is not visible Stores at room temperature Two-year shelf life
KEY Specifications

PRECAUTIONS G-BOND is flammable. Do not use near naked flame. Keep away from sources of ignition. Do not store large quantities in one area. Keep away from direct sunlight. G-BOND is volatile. Use in a well ventilated place. In case of contact with eyes, flush immediately with water and seek medical attention. In case of contact with oral tissue or skin, immediately remove with a sponge or cotton pellet. After the restorative treatment is finished, rinse thoroughly with water. If the tissue contacted by the material turns white or forms a blister, advise the patient to leave the affected area undisturbed, until the mark disappears, usually in 1-2 weeks. To avoid contact, it is recommended to apply cocoa butter to the area where rubber dam cannot cover. Avoid inhalation or digestion of material. When spilt on the table or floor, immediately wipe off with a dry cloth. Do not mix with other products. Dispose of all waste according to local regulations.

Directions To USE

How to Use Apply GC G-Bond to cut enamel and dentine Leave undisturbed for 5-10 seconds Dry thoroughly under MAXIMUM air pressure for 5 seconds in presence of vacuum suction Light cure for 10 seconds

Packaging

Kit Contains 1 x 5ml bottle 50 x Micro-tips 1 x Micro-tip Handle 1 x Dispensing dish