AXIMACK AXO Flow | Light Cured Universal Nano Flowable Composite Aro | Flowable Compoiste that Delivers High Strength Et Resistance

33% OFF

Rs.400.00 Rs.600.00

Free Shipping On Orders Above Rs. 2500.00

Description

#. AXO | FLOW IS LIGHT CURED UNIVERSAL NANO FLOWABLE COMPOSITE ARO I FLOW IS AN EXCELLENT FLOWABLE COMPOSITE THAT DELIVERS HIGH STRENGTH Et WEAR RESISTANCE

#. IT IS CHARACTERIZED BY OPTIMUM SURFACE AFFINITY, PENETRATES INTO MOST DIFFICULT AREA. IT COMBINES ESTHETICS AS WELL AS FLOW ON DEMAND HANDLING FOR USE.

#. Filling Of Smaller Cavities

#. Extended Fissure Sealing

#. Restoration Class III To V

#. Repairs Of Fillings & Veneers

#. Optimum Flowability

#. Higher Filler Loading Of 70% W/W

#. Excellent Physical Properties

#. Lower Polymerisation Shrinkage

#. Very Good Abrasion Resistance

Brand

Aximack

KEY Specifications

#.
COMPOSITION
AXO| FLOW Flowable Micro hybrid consists of multi-functional acrylic resins and fillers of .04-3 micron sized particles of inorganic fillers and pre polymerized composite (65% by weight, 45% by volume).
#.
INDICATIONS FOR USE
• Class V restorations
• Sealing margins
• Repairing pitted areas in hybrid restorations
• Small occlusal and lingual repairs
• Sealing gingival margins in Class II and Class III restorations• In deep Class V restorations to block out shine through prior to overlay of AXO| FLOW nanofill.
#.
PLACEMENT DIRECTIONS
Before treatment, tooth color should be assessed using a standard color guide. Keep the teeth moist when assessing the shade. For predictable results, use the same shade as your body composite. Prepare the cavity according to the general standards in composite filling therapy. Apply etching gel to entire cavity, beginning with enamel areas. Leave the gel for 20 sec on the tooth structure (total-etch technique). Remove the etching gel and spray the tooth with water for 15 seconds. Make sure no residue remains on the tooth. Dry cavity with oil-free air. Remoisten dentin and keep moist. Apply dentin adhesive, e. g. (AXO | BOND) according to the Instructions for Use and cure. For deep cavities with only a minimal layer of dentin over the pulp or those which have already had a small area exposed, the pulp should be indirectly or directly capped locally using calcium hydroxide compound. The calcium hydroxide compound should be covered with a glass ionomer cement before the AXO| FLOW Flowable nanohybrid is inserted into the cavity. Apply AXO| FLOW Flowable nanohybrid in thin layers (max. 2 mm). Polymerize each layer for 20-40 seconds (Halogen or LED lamp wavelength range of 400 - 500 nm) and final cure each restoration on all surfaces for 60 seconds.
#.
1. Seal Margins After placing restoration and sculpting toward margins, polymerize for 40 seconds. Next gently apply AXO| FLOW Flowable nanohybrid at the gingival margin by expressing a slight amount from the syringe along the entire margin and polymerize again, then polish. If a pit is seen at the gingival margin, roughen the area with a diamond bur, etch, wash and dry. Add bonding adhesive, then add a small amount of flowable to the defective area. Polymerize, finish and polish. 2. Seal Gingival Seat To completely seal the gingival seat area prior to placement of your composite, place a thin layer of AXO| FLOW flowable nanohybrid at that gingival seat area and polymerize. This reduces polymerization shrinkage and postoperative sensitivity.
3. To Start Deep Class V Restorations Where You Need to Block Shine-through Syringe Flowable Micro hybrid into deep areas of preparation after proper bonding technique and polymerize for 40 seconds. Then overlay with a final coat of AXO| FLOW nanofill
4. Finishing should be done with a combination of polishing materials such as diamonds, carbide burs and aluminum oxide discs in coarse and medium grits
5. Polishing can be achieved using aluminum impregnated instruments fine and superfine flexible discs, followed by polishing paste applied.
#.
STORAGE
• Once opened, do not refrigerate.
• Keep AXO| FLOW Flowable nanohybrid at room temperature (approximately 39-75 °F; 4-24 °C). • Do not use after expiration date.
• Avoid direct sunlight.
• Keep material out of reach of children.

Packaging

2 GRM X 1 SYRINGE